Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles Blog Blogs
  • Paul Woods's Avatar
    Today, 19:11
    Paul Woods replied to a thread Hi all in Introduce yourself
    Fingers crossed all of the noises are related to that.
    191 replies | 4448 view(s)
  • reedy's Avatar
    Today, 18:40
    reedy replied to a thread Hi all in Introduce yourself
    Yeah I agree not good! Upon further inspection it seems the gearbox isn't flush with the engine I'd like to hope that that is the cause Gonna...
    191 replies | 4448 view(s)
  • Paul Woods's Avatar
    Today, 18:35
    Paul Woods replied to a thread Hi all in Introduce yourself
    If Patrick gave you part numbers then I'd say they are correct. Bolt heads must be height checked to the clutch friction plate though. That...
    191 replies | 4448 view(s)
  • reedy's Avatar
    Today, 18:24
    reedy replied to a thread Hi all in Introduce yourself
    Not sure, was given the part numbers by Patrick chambers Yeah is does sound like that I hope it's just the exhaust rattling though....
    191 replies | 4448 view(s)
  • Paul Woods's Avatar
    Today, 18:07
    Paul Woods replied to a thread Hi all in Introduce yourself
    3vz-fe auto flexplate bolts or US 3vz-fe manual flywheel bolts? If it's the auto ones they are way too short. That sharp knocking immediately...
    191 replies | 4448 view(s)
  • reedy's Avatar
    Today, 17:29
    reedy replied to a thread Hi all in Introduce yourself
    I used 3vzfe flywheel bolts so diddnt think it would catch, guess I could have been wrong.... I hadn't noticed a bottom nock, I did replace all...
    191 replies | 4448 view(s)
  • Paul Woods's Avatar
    Today, 17:11
    Paul Woods replied to a thread Hi all in Introduce yourself
    You've probably installed the flywheel bolts without checking their depth or hat height to the clutch friction plate and it's catching on the bolt...
    191 replies | 4448 view(s)
  • rainen's Avatar
    Today, 16:46
    rainen replied to a thread Hi all in Introduce yourself
    Does sound like something is catching. You can have a go at dropping the gearbox off with the engine in or just drop the lot and have a look. Ive...
    191 replies | 4448 view(s)
  • samreedy's Avatar
    Today, 13:39
    samreedy replied to a thread Hi all in Introduce yourself
    Bugger! I push the clutch down 10mm and there's a horrible rattle Is it gonna be a take it all apart again job then I'm guessing ...
    191 replies | 4448 view(s)
  • notroubleclubber's Avatar
    Yesterday, 22:02
    notroubleclubber replied to a thread Hi all in Introduce yourself
    Well done mate!!
    191 replies | 4448 view(s)
  • DAN_REV1_TURBO's Avatar
    Yesterday, 21:47
    Attendee list amended!! Please check your name is on the list at the start of this thread, any problems or issue drop me a PM! Massive turnout this...
    19 replies | 2175 view(s)
  • samreedy's Avatar
    Yesterday, 17:37
    samreedy replied to a thread Hi all in Introduce yourself
    And she's back on the ground Just need some more jubilee clips for the radiator hoses and an exhaust system and jobs a goodin Think she...
    191 replies | 4448 view(s)
  • samreedy's Avatar
    Yesterday, 08:49
    samreedy replied to a thread Hi all in Introduce yourself
    Exciting times! Sent from my BLA-L09 using Tapatalk
    191 replies | 4448 view(s)
  • notroubleclubber's Avatar
    Yesterday, 07:23
    notroubleclubber replied to a thread Hi all in Introduce yourself
    Well done mate!!! Its a great feeling when you get one running. Hoping to get my turbo started today too.
    191 replies | 4448 view(s)
  • samreedy's Avatar
    21-04-2018, 20:51
    samreedy replied to a thread Hi all in Introduce yourself
    Yeah happy days Tomorrow's plan is to get the drive shafts in and gearbox seals and new gearbox oil Heater and rad hoses are next, need to heat...
    191 replies | 4448 view(s)
  • cdwood2010's Avatar
    21-04-2018, 19:11
    cdwood2010 replied to a thread Hi all in Introduce yourself
    Top work. :)
    191 replies | 4448 view(s)
  • samreedy's Avatar
    21-04-2018, 19:09
    samreedy replied to a thread Hi all in Introduce yourself
    I hadn't plugged the throttle sensor in haha Got all the vac lines done and intake lines and she starts and idles wooooo Lots and lots of...
    191 replies | 4448 view(s)
  • Paul Woods's Avatar
    21-04-2018, 18:23
    Paul Woods replied to a thread Hi all in Introduce yourself
    Ok check you have power on both black/Orange wires on the ISCV with ignition on.
    191 replies | 4448 view(s)
  • samreedy's Avatar
    21-04-2018, 18:18
    samreedy replied to a thread Hi all in Introduce yourself
    Exactly yes Sent from my BLA-L09 using Tapatalk
    191 replies | 4448 view(s)
  • Paul Woods's Avatar
    21-04-2018, 18:09
    Paul Woods replied to a thread Hi all in Introduce yourself
    If I'm reading that right, if you hold the revs up it runs constantly? Just not maintaining idle , is that right?
    191 replies | 4448 view(s)
  • samreedy's Avatar
    21-04-2018, 18:06
    samreedy replied to a thread Hi all in Introduce yourself
    Timing all looks good, everything's lined up so all seems ok there Sounds like a tractor with no backbox haha If I bring up the revs she's fine...
    191 replies | 4448 view(s)
  • Paul Woods's Avatar
    21-04-2018, 18:01
    Paul Woods replied to a thread Hi all in Introduce yourself
    Did you sort a timing issue?
    191 replies | 4448 view(s)
More Activity