Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles Blog Blogs
  • samreedy's Avatar
    Today, 11:23
    samreedy replied to a thread Hi all in Introduce yourself
    I replaced the stem seals so it can't be them I thought rings was more smoke at high revs not at idle? Either way it's a pain in the bollock...
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    Today, 09:22
    Paul Woods replied to a thread Hi all in Introduce yourself
    No, an open valve won't cause blue smoke, must either rings/valve stem oil seals or oil getting into the intake somehow.
    201 replies | 4646 view(s)
  • samreedy's Avatar
    Today, 08:15
    samreedy replied to a thread Hi all in Introduce yourself
    As the smoke is on idle is it more likely to be a valve leak than piston rings? Sent from my BLA-L09 using Tapatalk
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    Yesterday, 19:49
    Paul Woods replied to a thread Hi all in Introduce yourself
    Hmm, yep I agree, full teardown needed to find out what's gone wrong.
    201 replies | 4646 view(s)
  • samreedy's Avatar
    Yesterday, 18:53
    samreedy replied to a thread Hi all in Introduce yourself
    Yeah tell me about it! Rings were the right way up and staggered and I did check the gaps The big end bearings were straight from Toyota and...
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    Yesterday, 18:48
    Paul Woods replied to a thread Hi all in Introduce yourself
    There's a lot to deal with there, did you gap the rings before fitting? Are you sure the rings were fitted correct way up? Did you stagger the ring...
    201 replies | 4646 view(s)
  • reedy's Avatar
    Yesterday, 18:32
    reedy replied to a thread Hi all in Introduce yourself
    This is starting to do my head in now! Thought I had the clutch sorted, it goes in first and goes forward and goes in reverse and goes back but it...
    201 replies | 4646 view(s)
  • samreedy's Avatar
    Yesterday, 11:37
    samreedy replied to a thread Hi all in Introduce yourself
    Not sure yet, will have to video it to hear it again finished quite late last night so plan is to have a listen today after work Sent from my...
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    Yesterday, 06:58
    Paul Woods replied to a thread Hi all in Introduce yourself
    Has the start up knock gone away now?
    201 replies | 4646 view(s)
  • reedy's Avatar
    23-04-2018, 22:16
    reedy replied to a thread Hi all in Introduce yourself
    Managed to get her started and into gear So definitely going in the right direction
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    23-04-2018, 19:11
    Paul Woods replied to a thread Hi all in Introduce yourself
    Fingers crossed all of the noises are related to that.
    201 replies | 4646 view(s)
  • reedy's Avatar
    23-04-2018, 18:40
    reedy replied to a thread Hi all in Introduce yourself
    Yeah I agree not good! Upon further inspection it seems the gearbox isn't flush with the engine I'd like to hope that that is the cause Gonna...
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    23-04-2018, 18:35
    Paul Woods replied to a thread Hi all in Introduce yourself
    If Patrick gave you part numbers then I'd say they are correct. Bolt heads must be height checked to the clutch friction plate though. That...
    201 replies | 4646 view(s)
  • reedy's Avatar
    23-04-2018, 18:24
    reedy replied to a thread Hi all in Introduce yourself
    Not sure, was given the part numbers by Patrick chambers Yeah is does sound like that I hope it's just the exhaust rattling though....
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    23-04-2018, 18:07
    Paul Woods replied to a thread Hi all in Introduce yourself
    3vz-fe auto flexplate bolts or US 3vz-fe manual flywheel bolts? If it's the auto ones they are way too short. That sharp knocking immediately...
    201 replies | 4646 view(s)
  • reedy's Avatar
    23-04-2018, 17:29
    reedy replied to a thread Hi all in Introduce yourself
    I used 3vzfe flywheel bolts so diddnt think it would catch, guess I could have been wrong.... I hadn't noticed a bottom nock, I did replace all...
    201 replies | 4646 view(s)
  • Paul Woods's Avatar
    23-04-2018, 17:11
    Paul Woods replied to a thread Hi all in Introduce yourself
    You've probably installed the flywheel bolts without checking their depth or hat height to the clutch friction plate and it's catching on the bolt...
    201 replies | 4646 view(s)
  • rainen's Avatar
    23-04-2018, 16:46
    rainen replied to a thread Hi all in Introduce yourself
    Does sound like something is catching. You can have a go at dropping the gearbox off with the engine in or just drop the lot and have a look. Ive...
    201 replies | 4646 view(s)
  • samreedy's Avatar
    23-04-2018, 13:39
    samreedy replied to a thread Hi all in Introduce yourself
    Bugger! I push the clutch down 10mm and there's a horrible rattle Is it gonna be a take it all apart again job then I'm guessing ...
    201 replies | 4646 view(s)
  • notroubleclubber's Avatar
    22-04-2018, 22:02
    notroubleclubber replied to a thread Hi all in Introduce yourself
    Well done mate!!
    201 replies | 4646 view(s)
More Activity